Bimetallic cylinder liner 6 3/4 | AH220206-05040600 | 6 3/4″ bimetallic cylinder liner for F-2200HL type drill pumps. Full compliance with the stated catalogue number. Bimetallic sleeve, working life not less than 600 hours. Hardness of the working zone is 60…64 HRC, roughness is not more than Ra 0,4. Bimetallic layer should be made of wear-resistant, high-chromium cast iron of CHX28-32 grade (or better). Operation under conditions of nominal pressures for the given diameter of bushings, injection of weighting packs and colmatant, drilling mud on hydrocarbon base up to 90% (DT/oil) with density from 0,83 to 2,2 g/cm3. The permissible pressure for which the sleeve is designed is 34.2 MPa. | F-2200HL Bomco |
Piston rod AH220203-0503 Bomco | AH220203-0503 | The diameter of the seat is 42 mm. Working medium – drilling fluid on hydrocarbon base up to 90% (RUO), density from 0,83 to 2,2 g/cm³. Drilling fluid temperature up to 100°C Maximum pressure 52MPa Ambient temperature +45°C – 50°C |
F-2200HL Bomco |
Valve spring AH100101-0529 Bomco | AH100101-0529 | 1. Valve spring AH100101-0529. 2. Working medium – Water, oil products, salt, clay and cement solutions. Drilling fluids with density from 0,83 to 2,2 g/cm3, with sand content not less than 3%. Drilling mud temperature up to +100°C Maximum pressure 52MPa Ambient temperature +45°С – 50°С. |
F-2200HL Bomco |
Filter AH160201-020202B1 Bomco | AH160201-020202B1 | In accordance with the manufacturer’s CD. | F-2200HL Bomco |
Pin AH000006-0308 Bomco | AH000006-0308 | shear pin of safety valve JAF-3-52 | F-2200HL Bomco |
Pneumatic chamber AK755201-0400 | AK755201-0400 | Analogue / Heat-resistant pneumatic chamber AK755201-0400B1 of compensator WY-75-52, P-52 MPa; Working medium – drilling mud on hydrocarbon base up to 90% (RUO), density from 0,83 to 2,2 g/cm³. Drilling fluid temperature up to +100°C Ambient temperature +45°С – 50°С |
F-2200HL Bomco |
Seal AH220206-050700 Bomco | AH220206-050700 | Set of seals for pressure cover of discharge valve catalogue number (f206,38) AH220201-0525B2 and AH220206-050700. Working medium – drilling mud on hydrocarbon base up to 90% (RUO), density from 0,83 to 2,2 g/cm³. Drilling fluid temperature up to +100°C Maximum pressure 52MPa Ambient temperature +45C – 50C |
F-2200HL Bomco |
Ring AH220201-0524 Bomco | AH220201-0524 | Sealing ring of discharge pipe; AH220201-0524. Working medium – drilling mud on hydrocarbon base up to 90% (RUO), density from 0,83 to 2,2 g/cm³. Drilling fluid temperature up to +100°C Maximum pressure 52MPa Ambient temperature +45°C – 50°C |
F-2200HL Bomco |
Plate AH220206-0505 Bomco | AH220206-0505 | Wear plate; AH220206-0505. Working medium – hydrocarbon based drilling mud up to 90% (RUO), density from 0,83 to 2,2 g/cm³. Drilling fluid temperature up to +100°C Maximum pressure 52MPa Ambient temperature +45C – 50C |
F-2200HL Bomco |
Nut T501-303.00 Bomco | T501-303.00 | In accordance with the manufacturer’s CD. | F-2200HL Bomco |
Ring AH160201-0115 Bomco | AH160201-0115 | Wear plate O-ring AH160201-0115 Working medium – hydrocarbon based drilling mud up to 90% (RUO), density from 0,83 to 2,2 g/cm³. Drilling fluid temperature up to +100°C Maximum pressure 52MPa Ambient temperature +45C – 50C |
F-2200HL Bomco |
Flange AH220206-0506 Bomco | AH220206-0506 | In accordance with the manufacturer’s CD. | F-2200HL Bomco |
Ring AH130101-0512B1 Bomco | AH130101-0512B1 | Cylinder liner packing AH220201-0512B1; Working medium – drilling fluid on hydrocarbon base up to 90% (RUO), density from 0,83 to 2,2 g/cm³. Drilling fluid temperature up to +100°C Maximum pressure 52MPa Ambient temperature +45°C – 50°C |
F-2200HL Bomco |
Gland ring AH220201-0520 Bomco | AH220201-0520 | Hydraulic cylinder packing ring AH220201-0520. (O-ring between the discharge/suction box). Working medium – hydrocarbon-based drilling mud up to 90% (HFO), density from 0.83 to 2.2 g/cm³. Drilling fluid temperature up to +100°C Maximum pressure 52MPa Ambient temperature +45°C – 50°C |
F-2200HL Bomco |
Ring 345×7.0-G-S, GB/T3452.1-2005 | 345х7.0-G-S, GB/T3452.1-2005 | In accordance with the manufacturer’s CD. | F-2200HL Bomco |
Ring AH160201-0116B6 Bomco | AH160201-0116B6 (For liner 6 3/4″) | Cylinder sleeve O-ring cylinder (φ220) AH160201-0116B6 (for 6 3/4″ bushing) Working fluid – up to 90% hydrocarbon based drilling fluid (HFO), density from 0.83 to 2.2 g/cm³. Drilling fluid temperature up to +100°C Maximum pressure 34.2MPa Ambient temperature +45°C – 50°C |
F-2200HL Bomco |
Ring AH220201-0527B1 Bomco | AH220201-0527B1 (For linerу ф 5 1/2″) | Sealing ring of the sleeve cylinder (φ190) AH220201-0527B1 (under bushing of 5 1/2″) Working medium – drilling mud on hydrocarbon base up to 90% (RUO), density from 0,83 to 2,2 g/cm³. Drilling fluid temperature up to +100°C Maximum pressure 34.2MPa Ambient temperature +45°C – 50°C |
F-2200HL Bomco |